I purchased a surplus Currie Technologies “Diagnostic” throttle. (Which includes 3 LED’s labeled as 1/3, 2/3 and full charge indicators) It has a six pin (7 cable) connector with no pin-out diagram.
After opening it up, it appears that the blue, black, and red wires are connected to the throttle sensor itself, while the other four wires (White, Gray, Yellow, Green) connect to the LED circuit board.
The pin-out ordering is as follows, from the bottom of my picture up:
- Red/White (Throttle/LED, sharing a pin, + voltage)
- Black (to throttle, I assume Ground)
- Blue (from throttle, I assume signal)
- Green (Full LED)
- Yellow (2/3 full LED)
- Gray (1/3 full LED)
I connected the Red/Black/Blue wires to a motor speed controller that had a 3 wire throttle connection (matching them up to the Red/Black/Green wires from the controller) and it worked great!
The LED pin-out is as follows:
White (positive / Vcc)
Gray – 1/3 empty LED
Yellow – 2/3 full LED
Green – Full LED
Note that I was able to get the LED’s to light up with a 3V source, but I believe their forward voltage is less than 3V and you should use a current limited supply so that you do not burn the LED’s out.
Jay – Help! where did you find a 6 wire throttle? My daughters Schwinn needs one and I’ve been told there discontinued.
They have been discontinued. I purchased this one surplus from AllElectronics.com
Pingback: Jay’s Technical Talk › Electric Bicycle power circuit
Pingback: Jay’s Technical Talk › The $175 Electric Bike
I have 6-wire throttles, just drop me a line.
Albuquerque Electric Cycles
Hello there! I need a 6 pin throttle for a s500 scooter. Thanks!
Good morning- Do you still have 6 pin throttle cables for the Schwinn S500 ?
Need the 6 pin throttle you got any
I do not have any for sale.
As long as you don’t care about the indicator LED’s, you can use only the 3 throttle pins by attaching the correct 3 wires from a 5pin or 3pin throttle.
Amazon has a 5pin throttle here: https://amzn.to/3Obczp9
Or you can get a 3 pin version here: https://amzn.to/3ObcEcr
We have them in stock and listed on these pages:
Tom Gamble I need a 6pin throttle for a Schwinn S500
I need one of the Six pin throttles also
Great info here thanks 🙂 My problem is, My Schwinn 1000 throttle lights (3) stays on all the time, any here can help with that please?
It is a 5 pin (wires) throttle. Lights are indicators are : Full, Half and Empty. . .
I’m not familiar with that one, but it sounds like either a few wires going to the LED’s are shorted out somewhere in the line, or your controller has a problem.
I have a 6 pin throttle but a 4 pin controller… Help?
It is likely that your throttle does not include the optional status LED’s (or at least, not as many of them). If you can figure out which three main wires to hook up (ground, +v and signal) and how, it may still work (assuming the throttle is of the same type. (resistance / hall effect, etc…)
Brilliant! Was looking for a replacement throttle, now I can buy a cheap 6 buck one off of ebay with no fear. Who needs LEDs anyway? 🙂
Can A 5 pin throttle be used to replace 6 pin throttle for a swinn s500, if so how do I rewire to work?
It may be possible, as long as the five pin cable has the same control signals from the throttle as the six pin cable. You would only have to connect the first 3 wires
1.Red/White (Throttle/LED, sharing a pin, + voltage)
2.Black (to throttle, I assume Ground)
3.Blue (from throttle, I assume signal)
For the throttle portion to work (ignoring the other wires if you don’t need the LED indicators to work.)
Do they make a 7 pin throttle? It looks like that is what I have
I would not be surprised to find a 7 pin version on one of their later models, but I do not have any technical information about them.
Looking for 6 pin twist throttle for Schwann S350. Anyone know where I can find one?