![\"\"](\"https:\/\/www.summet.com\/blog\/wp-content\/uploads\/2017\/01\/IMG_20170108_102052.jpg\")
<\/a>\nInside, there is a Pi shaped piece of aluminum extrusion that acts as the heatsink for the MOSFETS and freewheeling diodes, as well as being electrically connected to the motor – terminal. It is held against a large thermally conductive, but electrically insulating pad, which separates it from the controller case, but allows heat to be dissipated. It is held in place with 8 screws that pass through insulating plastic brackets into the bottom of the case.<\/p>\n
People online had told me that these screw holes were “potted”, but on my controller they were just filled with two rubber plugs.They also told me that you could not cut through the Curtis potting material with a razor knife. [This super hard potting material was also prone to cracking at the edges and letting moisture into the controller, so a flexible rubber like material is better anyways…]<\/p>\n <\/p>\n So either my controller had already been opened up, or Curtis had decided to use rubber plugs for the holes and a more flexible potting material on the controller that I had. (There was a “Warranty void if seal broken” sticker on the front, and as far as I could tell the inside of the controller was completely stock, so I’m leading towards Curtis just using a different potting material, but it’s possible somebody may have already repaired it once using exact replacement parts and put their own warranty sticker on it. There were some markings inside that might be from the factory, or might be from a repair shop you’ll see photos of farther down.)<\/p>\n I removed all 8 screws and plastic bushings from the bottom, and then cut around the potting material “end-piece” on the front (terminal) side and pulled the entire controller unit out of the aluminum extrusion case. \u00a0 Then I had to cut around the terminals and pulled the potting material off the front. It had some type of fiberglass panel between the potting material and the piece of black foam behind it. \u00a0 I was not able to remove the potting material and fiberglass panel in one piece, so if\/when I put it back together I’ll just have to re-pot it with black silicon.<\/p>\n Once the guts were removed, I could see a spot under the control board where some power electronics had fried. \u00a0 [The common failure mode for these controllers is for the MOSFETS nearest to the logic control board to blow up, because they turn on just slightly sooner than the other MOSFETS due to the propagation delay of electricity through a wire.]<\/p>\n I had to unsolder the 7 connections between the logic board and the power board (as well as a 2 wire thermocouple) so that I could remove the logic board and see the blown power electronics. The immediate problem was not hard to spot…<\/p>\n Curtis 1231c-8601 power board components<\/strong><\/p>\n The Curtis 1231c-8601 power board is relatively simple. It uses 18 MOSFETS in parallel to switch current from the motor- terminal back to the battery- terminal (the motor+ lead is already connected to battery+). The MOSFETs it uses are IXYS IXTH50N20 SP9536 chips. The center lead is bent up over the chip and soldered to a ring terminal, such that the screw that attaches the chip to the heat sink also electrically connects that pin to the heat sink. \u00a0 Most chips that attach to a heatsink have a metal back, but the IXTH50N20’s used here do not, so it appears that they had to take extra assembly steps to electrically couple it to the heatsink. The power MOSFETs have \u00a0 a 47 ohm resistor on their gate drive line. Such a high value was chosen to deliberately slow down the switching of the MOSFETS, so that the ones nearest to the logic circuit would not be able to turn all the way on before the ones farther away had a chance to shoulder some of the load. It would appear that this strategy was not entirely successful, as the closest MOSFETs blowing up is a common failure mode.<\/p>\n Near each MOSFET is a freewheeling diode (used to conduct current between the motors +\/- terminals when the MOSFETS are not conducting current from the battery. They are TSR2402R 7103 K units, which basically have two sheets of metal with a round diode mounted between them. They are “reverse polarity” \u00a0 Schottky diodes, which means that the anode is connected to the heatsink by the screw (as well as being connected to the power PCB by a lead. Unfortunately, they are difficult to source replacements for in this form factor. \u00a0 Fortunately, they usually do not blow up like the MOSFETS.<\/p>\n <\/p>\n Here is a bottom view of one of the failed MOSFETs:<\/p>\n One leg was completely melted. The arcing electricity actually ate some of the metal case of the diodes that were mounted next to the MOSFETS! (amazingly, these diodes appear to be still working.)<\/p>\n In addition to the obvious damage to two of the MOSFETs, I noticed a third mosfet that has some residue around it. Although not as obviously blown apart, this guy may have issues as well. In general, when one MOSFET in the set blows up, you should replace them all, as others may have been overstressed and ready to fail.<\/p>\n Also, a trace on the logic board has been blown away. If you look at the four wire connector just to the left and above the white “ORB-102 w\/o 60355 rev.M” sticker, you will see that the second pin from the right leads to a trace that has acted like a fuse. Arcing electricity probably got it. There were also a few traces on the power board that will need to be fixed.<\/p>\n <\/p>\n Here are a few shots of the Pi shaped heatsink showing where all the MOSFETS and diodes were attached on one side and the soot pattern.<\/p>\n <\/p>\n I should also mention that the 1231c has the option to “plug brake” (more for forklift operation than on-road vehicle usage) and has six plug braking diodes connected to an A2 terminal that is unused in my application. I just unscrewed the entire connector assembly and A2 terminal, and will probably not bother re-installing it as I don’t need it.<\/p>\n I found a few hand markings inside the terminal. One was the “OV 174” pictured above, and the other was this “CIL \/ M1” on the cardboard shield that fit between the power electronics and the logic board.<\/p>\n In addition to the MOSFETS and Diodes, the power board also has 35 capacitors used to reduce ripple as the MOSFETs switch. They are Nichicon 220 uf 200v electrolytic capacitors. There was also one other component attached to the heatsink (but electrically isolated with a silicon pad). it was a Vishay IRFP254 532P power MOSFET at location Q13.<\/p>\n This MOSFET is used as a 24 volt voltage regulator to power the logic part of the circuit<\/p>\n <\/p>\n <\/p>\n <\/p>\n Here is a video of the procedure:<\/a><\/p>\n \u00a0 <\/a><\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a> <\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n
\n<\/a><\/p>\n
\n<\/a><\/p>\n<\/a><\/p>\n
\n