Solar Panels on the Electric Truck

Two 175 watt solar panels mounted to the bed cover of my electric pickup truck.
I purchased two used GE Energy GEPVc-175 watt solar panels and mounted them to the bedcover of my truck using 10-24 machine screws and T cone washers as rubber vibration dampers. Each panel weighs 31 pounds, and is rated to deliver up to 175 watts of power in full sun (at around 36 volts each, or 73.4 volts at 4.7 Amps in series). I am still waiting on a group of Georgia Tech ECE students for the magic box that does maximum power point tracking (MPPT) and voltage boosting to charge my 120 volt battery pack, but I hope to be generating 1-3 miles of my daily commute from the sun soon. As my daily commute is 4 miles, this can be a significant percentage of my total energy usage.
Diagram showing the panel layout over bed cover support structure.

I have calculated that in the summer the panels are far enough behind the cab that they will not be shadowed by it, even if I have to park facing south. In the winter and early spring / late autumn I need to park facing north to avoid shading a strip of the solar panels.
I still need to figure out a way to tilt the panels towards the sun to collect as much energy as possible. This is especially critical during winter, when the solar angle is way off of vertical. As the bed cover tilts, AND the bed of the truck can tilt (the other way) I figure I can work something out (with a few pieces of wood cut to the correct height, or linear actuators if I want to get fancy.

11 thoughts on “Solar Panels on the Electric Truck

  1. Pingback: Adventures with a boost converter — Jay’s Technical Talk

  2. I would like to implement a MPPT on a PIC controlled system: any help for the program ?
    I have to charge a 12 v sla battery using a PV .
    Thanks
    Bye
    Ambrogio

    • I am still working on the code for a MPPT as part of a boost converter. You can see my initial schematic here:

      https://www.summet.com/blog/2012/01/22/boost-converter-schematic/

      Note that my system is more complicated than what you want, as I am boosting the voltage up. For a 12V battery charger, you could get away with a simple MOSFET switch acting as a PWM, so that you could choose what voltage to keep the solar panel at. The other parts of my schematic (current sensing, voltage sensing) will be useful for you, but you could replace the inductor/capacitor boost part with just a single PWM ing MOSFET and a filter capacitor.

  3. This seems like a good idea in theory, but how do you haul anything in your truck if it is loaded with a solar panel? Seems impractical.

    • 95% of my trips in the truck are for commuting to the train station, not hauling stuff. For trips to the grocery store I can simply slide bags in via the tailgate. For large items, the panels are mounted to a hinged bed cover. I can tilt the cover up about 45 degrees which allows me to put relatively large items in the back of the truck without removing them (if I’m willing to rest the cover on top of whatever I am carrying). Worst case scenario, with another person to help me lift, the entire cover can be taken off the back of the truck, panels and all.

  4. hi jay,i have built my own solar panels and want to start a truck,your s-10 is my exact vision!i would also like to figure out how to charge on the fly…i have an old guy that has a patent on a horizontal turbine and was thinking of mounting these on the bed the same as your panels..i also have found batteries that 1 would replace 4 reg deep cycles (120lbs each)also do you need higher voltage or amperage for max efficientcy?i was hoping to go 100 miles on these 4 batteries? oh how much do have in your build? any direction on how to go would be appreciated thanks

    • Hi Phillip,

      I have 20 six-volt golf cart batteries in my truck (they weigh about 1200 lbs total). It sounds like you have about the equivalent to 16 of my batteries (or perhaps 8….my batteries come in close to 60 lbs each). So, it sounds like your batteries would have less capacity than mine. With my battery pack I can easily drive 20 miles. If I push the battery pack, I can drive 30 to 35 (and completely destroy the batteries by discharging them to 0%). My truck does not have low rolling resistance tires on it, so if you had less weight and super low rolling resistance tires, you could possibly get a similar range with your S-10 and the batteries you described.

      However, to get a 100 mile range you must go with Lithium Ion batteries, and they will cost many thousands of dollars. I find that 20 miles a charge (I can drive 40 miles in a day if I charge in the middle of the day) is plenty of range for my short commutes. If you are regularly driving 100 miles a day, a fuel efficient hybrid car may be a better choice for you.

      The solar panels provide very little energy (Enough for almost 2 miles of driving a day), and I suspect a wind turbine that low to the ground wouldn’t provide much more power unless you live in a very windy area, so plan on plugging in your truck. You might want to check out this website for S-10 conversion information:
      http://www.evamerica.com/evtrucks.html

  5. I put a down payment reserve on Rivian’s 2020 pick-up truck. I also sent them an email suggesting they do exactly what you’ve done here. Install a solar panel in the flat bed floor. I haven’t heard back from them yet though.

  6. has anybody thought about the new f150 lighting and putting solar panels on it to charge the batteries to get more rande out of it?

Leave a Reply to lynne whelden Cancel reply

Your email address will not be published. Required fields are marked *