This is a 3D printed Resin base from BiteTheBullet Studio. I’m going to show you the steps I used to paint it.
HOWTO Paint: Forest Scene Base
1
3D printed Prescription Lens Inserts for Oculus Go
I’ve always wanted Prescription Lens inserts for my Oculus GO VR headset. But I just couldn’t justify the $80 price just so I wouldn’t have to wear my glasses while using the VR headset.
Then I found this project on Thingiverse: Oculus prescription lens adapter (Quest 2, Quest and Rift S)
That’s right, you can 3D print your own adapters that will convert a standard round eyeglass lens (such as you receive if you order Zenni Optical Round Glasses 55002. Which just happen to only cost $35 in my prescription).
Seven days later, I was ready to mark the correct orientation, take the lenses out of the glasses (requires a small screwdriver), and pop them into my 3D printed adapters.
The “Version1” adapters pop right into my Oculus GO (which apparently are the same size as the original Quest), and now the VR headset fits more comfortably on my face (no more distracting gap around the nose area!).
Plus, I can give my son the now empty frames to have fun playing Harry Potter….
Update – July 19th 2022:
The lenses are working well in the Oculus Go, but after about 8 hours of use the right hand lens holder loosened up and stopped “gripping” the Occulus socket and holding in the foam. I believe one of the small “lips” printed along the bottom had either snapped or had gotten worn down. I printed a replacement part and before installing I dipped it in low viscosity epoxy resin. This made the part significantly more rigid (and smoother). I found it easier to install the lens (possibly due to experience) and it had a very satisfying grip on the Oculus. If you are installing for the first time and have access to low viscosity epoxy, I’d recommend using it. (I also wonder if superglue would have a similar effect….) My left hand lens mount is still holding strong, so I’m not going to mess with it at this time.
May 2022 energy rates – Duke Energy – Orlando Florida
Residential Service rates for Duke Energy (Florida):
$12.45 per month Customer Charge *
13.082 cents per kWh (first 1000 kWh)
15.039 cents per kWh (all kWh above 1000)
* – Duke also imposes a 30$ minimum bill adjustment, so if you use less than 134 kWh of power ($17.55 of electricity usage + 12.45 customer connection charge = $30) they will add a Minimum Bill Adjustment so that your total charges are $30 (+3.37 of taxes in Orange County Florida) for a total minimum bill of $33.37
Painting the Castle Ravenloft Skeletons
I painted the three Castle Ravenloft board game Skeletons with slightly different colors (mostly on the shields and swords, but the bones have different levels of tints on them as well) so that people could say things like “I want to aim at the one with the blue shield!”.
The general approach for bones is to do shades of gray/white first, then tint them with a bright yellow wash, followed by a transparent dark brown (burnt umber) wash. Variations in lightness and color can be made by the lightness/darkness of the base coats, and amount of washes you use.
VECY’s CR60 car Fridge / Freezer (Dual Zone) Review
I reviewed the VECY’s CR60 car refrigerator / freezer. It is a 60 L wheeled cooler with built in dual zone compressor heat pump. It has a dual zone control panel that can maintain temperatures between 68F down to -4F, and is powered by 12-24 volts DC. (It also includes an AC adapter to power it from 120-240v AC.)
You can watch my 5 minute summary review here:
(I also have a 30 minute long full review…but unless you are REALLY interested…the summary review gives you all you need to know.)
If you would prefer to read your review, here are the relevant details:
Battery Tray / Door discoloration on First Alert Smoke Detector (2018, SA511)
When changing smoke detector batteries on my First Alert SA511 smoke detectors, I noticed that ONE (of the six) has a discolored battery tray/door. It appears that the plastic used to make the battery tray was of a different composition from the rest of the shell, as it has turned yellow with age, while the rest of the smoke detector has not. (Also, my other five smoke detectors all have pure white battery trays that match the body as well…) Continue reading
It’s March 2022, how is Orange County (FL) doing with Covid-19?
The number of confirmed COVID-19 cases in Orange County last week was 2,018, as low as in mid-December of 2021. The Omicron surge is mostly over, and the new case positivity rate has dropped to 6.9% (close to the < 5% threshold that indicates community spread is under control).
While the total number of cases in the Omicron surge was significantly higher than in the Delta surge, the number of hospitalizations (orange line) was slightly lower, and the number of deaths (blue area) is significantly lower. This is partially due to a larger percentage of the population being vaccinated, partially due to the nature of Omicron (infecting the upper respiratory tract more than the lungs), and partially due to survivor bias from prior waves.
According to the CDC, a total of 3,089 covid-19 related deaths have occurred in orange county , or 212 deaths per 100,000 residents. The total number of confirmed cases is at 371,647, with more than 1 in 4 residents having been infected over the course of the pandemic.
I am hopeful that by next week the test positivity rate will fall below 5%. The CDC community status tracker just recently changed from orange to yellow:
HOWTO: Paint Flames
Sometimes you need to paint fire. The color light that fire throws out depends upon it’s temperature, generally ranging from white to red (we will ignore blue flames for the purposes of painting miniatures). Here are a few items I’ve painted with Flame effects.
ezShare (ez Sh@are) Wi-Fi SD Card – Works with Linux (and any WiFi enabled device with a web browser)!
A while back I purchased a generic Wifi Micro-SD card adapter that didn’t work with my Linux computer due to the proprietary protocol it used. This ez Sh@are 32GB SDHC +Wi-Fi card is what I should have purchased in the first place.
When powered in the camera, it acts as an AP and broadcasts a Wi-Fi network (default SDID: ez Share, default PW: 88888888 – eight eights) that you can connect to with any laptop or phone. It captures your browser and directs it to a “ezshare.card” web-server that displays the photos on your SD card. (If that doesn’t work, you can direct your browser directly to 192.168.4.1).
You can view thumbnail previews of the images, and download a single image, or a selection of images (as a tar file) or all images in the folder (again, as a tar file).
If you want to see or download videos on the card, you need to select the “Video Gallary” link (it doesn’t show previews of the videos).
The only configuration options are to change the SSID of the network, the WiFi network password, and the administrative password (the default admin password is “admin”). You should change the wifi password and the admin password if you don’t want random people downloading the photos from your SD card anytime your camera is on.
If you mess up the configuration, or find a ezShare WiFi card that you can’t access, the configuration is stored in a file on the card, so if you format the card it will overwrite the configuration and go back to the defaults.
I bought the 32GB card that includes a “share” (or not) switch on the bottom that gives you the option to turn off the WiFi AP when you don’t want to export one (Airplane mode, or to save power). You can also purchase a TF/MicroSD card “adapter” version, that includes the WiFi server, but does NOT include any memory, allowing you to insert a larger sized MicroSD card if you need more than 32 GB of storage.
Using the DAJA DJ6 Laser engraver under Ubuntu Linux
This is the DAJA DJ6 laser engraver. It is basically a 450nm solid state laser diode (3 Watt according to the manual) attached to an X/Y gantry that can do laser engraving.
Although it does not offer Linux software support, you CAN use it with a Linux desktop. Read on for how I got that working.
Continue reading